Inconel 600 Pipe Fittings
Inconel Alloy 600 Elbow, Inconel 600 90 degree Elbow, Inconel 600 Buttweld Fittings, Nickel Alloy 600 Pipe Fittings at Best Price in India.
VM Energy Solutions INC is a recognised stockist and distributor of Inconel Alloy 600 Pipe Fittings, which has notable welding characteristics. Inconel UNS N06600 Reducer Pipe Fittings gives excessive strength for roll formed structural additives and low work hardening rate grade for cold heading fasteners. It can get marked up with the aid of using fingerprints and grease, increase discoloration, and subsequently rust. They had been found on the surfaces of chromium, iron, and stainless steel after publicity to liquid sodium at six hundred Degree C and above. We will show off this steel and illustrate the kind of corrosion resistant, mechanical and bodily properties which decide its suitability for a huge variety of applications. The molybdenum on this alloy is delivered to assist withstand corrosion to chlorides (like sea water and de-icing salts).
- Inconel 600 Pipe Fittings Standard Specification
- Inconel 600 Buttweld Fittings International Standard
- Inconel 600 Pipe Fittings Equivalent Grade
- Different Forms of Inconel Alloy 600 Pipe Fittings
- Inconel 600 Pipe Fittings Chemical Composition
- Inconel Alloy 600 Pipe Fittings Mechanical Properties
- Inconel 600 Buttweld Fittings Thickness Chart
- Inconel 600 Pipe Fittings Tolerance Chart
- Largest Inventory Of Inconel 600 Pipe Fittings
Inconel WNR 2.4816 Concentric Reducer Pipe Fittings is low steel which incorporates chromium; and it's far this addition of chromium that offers plain steel its specific stain and corrosion resisting properties. There isn't any enterprise identified definition for this product alien though it's far mechanically utilized by many end-users. This product has its personal specific properties for tensile strength, melting factor, oxidation resistance, and corrosion resistance. The molybdenum offers this steel higher usual corrosion resistant property, especially better resistance to pitting and crevice corrosion in chloride environments. It is magnetic and may be hardened through cold working.
Inconel® Alloy 600 Reducer, DIN 2.4816 45 Degree Elbow, ANSI B16.9 Nickel Alloy 600 Stub End, Alloy 600 Pipe Tee, ASTM B366 Inconel Alloy 600 Pipe Fittings, UNS N06600 Pipe Cap, Inconel 600 Pipe Elbow Supplier in Mumbai, India.
Titanium stabilization improves this Nickel Alloy 600 Eccentric Reducer Pipe Fittings concerning susceptibility to inter-granular corrosion and, consequently its use within the sensitization variety, among the tiers of 427 Degree C to 816 Degree C. They are automobile exhaust grade – weld stabilized, and additionally immune to mildly corrosive environments. They have barely one-of-a-kind alloy composition, and consequently barely one-of-a-kind bodily characteristics. It is an excessive hardness martensitic steel, in which in strip form, its dominant use is for excessive quality knife blades. We make certain we get this alloy with each cargo we get hold of in order that we are able to guarantee our clients that the enclosure and its components are built of the exact steel material, as distinct and ordered.
We Keep Bulk Stock Of UNS N06600 Pipe Bend, Inconel 600 Pipe Fittings at Our Stockyard, Check Inconel Alloy 600 Welded Fittings Dimension, Buy Alloy 600 Seamless Pipe Fittings at an Affordable Price In India.
Inconel 600 Pipe Fittings Standard Specification
| Specifications | ASTM B366 / ASME SB366 |
|---|---|
| Dimensions | ASME/ANSI B16.9, ASME B16.28, MSS-SP-43, BS4504, BS4504, BS1560, BS10 ASME 16.11, MSS SP-79, 83, 95, 97, BS 3799 |
| Size | Seamless Fittings: 1/2" - 10" Welded Fittings: 1/2" - 48" |
| Thickness | SCH10, SCH20, SCH30, STD SCH40, SCH60, XS, SCH 80, SCH 100, SCH 120, SCH 140, SCH 160, XXS available with NACE MR 01-75 |
| Manufacturing Standards | ASME/ANSI B16.9, ASME B16.28, MSS-SP-43 DIN : DIN2605, DIN2615, DIN2616, DIN2617, DIN28011, DN15-DN1200 BS : BS4504, BS4504, BS1560, BS10 JIS : JIS B2311, JIS B2312, JIS B2313, JIS B2316 GOST : GOST 17375, GOST 17376, GOST 30753, GOST 17378, GOST 17379, GOST 17380 EN: EN10253-1, EN10253-2 |
| Types | Seamless / ERW / Welded / Fabricated |
| Connection | Welding |
| Bending Radius | R=1D, 2D, 3D, 5D, 6D, 8D, 10D or Custom |
| Elbow | Angle : 22.5 deg, 30deg, 45 deg, 90 deg, 180 deg, 1.0D, 1.5D, 2.0D, 2.5D, 3D, 4D, 5D, 6D, 7D-40D. Standard: ASME B16.9, ASME B16.28, ASME B16.25, MSS SP-75 DIN2605 JISB2311 JISB2312 JISB2313, BS, GB, ISO |
| Manufacturing process | Push, Press, Forge, Cast, etc. |
| Specialized manufacturer of | 90º Elbows, Couplings, Reducers, Inserts, Caps, Nipples, 45º Elbows, Tees, Crosses, Equal Tees & Reducing Tees |
| Test Certificates | EN 10204/3.1B Raw Materials Certificate 100% Radiography Test Report Third Party Inspection Report, etc |
| Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2, Test Certificates certifying NACE MR0103, NACE MR0175 | |
Inconel 600 Buttweld Fittings International Standard
| Standard Code | Standard Name |
|---|---|
| American Steel Pipe Fittings Standard | |
| ANSI ASME SA-403 | Forged Durimet pipe fittings |
| ANSI ASME B16.9 | Factory-Made wrought steel pipe fittings |
| ANSI ASME B16.28 | Wrought steel butt-welding short radius elbows and returns |
| ISO 5251 | Stainless steel butt-welding fittings |
| MSS SP-43 | Wrought stainless steel butt-welding fittings |
| MSS SP-75 | Forging butt-welding fittings |
| German Steel Pipe Fittings Standard | |
| DIN 2605 | Steel butt-welding pipe fittings.elbows and bends |
| DIN 2615 | Steel butt-welding pipe fittings.tees |
| DIN 2616 | Steel butt-welding pipe fittings.reducers |
| DIN 2617 | Steel butt-welding pipe fittings.caps |
| Japanese Steel Pipe Fittings Standard | |
| JIS B2311 | Universal steel butt-welding pipe fittings |
| JIS B2312 | Steel butt-welding pipe fittings |
| JIS B2313 | Steel plate butt-welding pipe fittings |
| Other Steel Pipe Fittings Standard | |
| EN 1025 | 3 Butt-welding pipe fittings |
Inconel 600 Pipe Fittings Equivalent Grade
| STANDARD | UNS | WERKSTOFF NR. | AFNOR | EN | JIS | BS | GOST | OR |
| Inconel 600 | N06600 | 2.4816 | NC15FE11M | NiCr15Fe | NCF 600 | NA 13 | МНЖМц 28-2,5-1,5 | ЭИ868 |
Different Forms of Inconel 600 Pipe Fittings
Inconel 600 Elbow
Inconel 600 Stub End
Inconel 600 Cross
Inconel 600 Pipe Cap
Inconel 600 Tee
Inconel 600 Pipe Bend
Inconel 600 Pipe Nipple
Inconel 600 Concentric Reducer
Inconel 600 Eccentric Reducer
Inconel 600 Pipe Fittings Chemical Composition
| Grade | C | Mn | Si | S | Cu | Fe | Ni | Cr |
| 600 | 0.15 | 1.00 | 0.50 | 0.015 | 0.50 | 6.00 - 10.0 | 72.00 | 14.00 - 17.00 |
Inconel Alloy 600 Pipe Fittings Mechanical Properties
| Grade | Density | Melting Point | Yield Strength (0.2%Offset) | Tensile Strength | Elongation |
| 600 | 8.47 g/cm3 | 1413 °C (2580 °F) | Psi - 45,000 , MPa - 310 | Psi - 95,000 , MPa -655 | 40 % |
Bulk Stock of Inconel® Alloy 600 Pipe Fittings, Rate of ASTM B366 Inconel 600 Pipe Cap in India, Check online Alloy 600 Elbow Pressure Ratings, Largest DIN 2.4816 Reducer Stockist in India, We offer Inconel 600 Stub End in almost all Sizes.
Inconel 600 Buttweld Fittings Thickness Chart
| Product range and theoretical weights (kg) | |||||||||
| DN | Schedule 10S | Schedule 40S | Schedule 80S | ||||||
| 90° Elbow | 45° Elbow | Equal tee | 90° Elbow | 45° Elbow | Equal tee | 90° Elbow | 45° Elbow | Equal tee | |
| 8 | 0.02 | 0.01 | 0.03 | 0.03 | 0.02 | 0.06 | 0.04 | 0.03 | 0.07 |
| 10 | 0.03 | 0.02 | 0.05 | 0.03 | 0.02 | 0.03 | 0.06 | 0.04 | 0.09 |
| 15 | 0.06 | 0.03 | 0.09 | 0.08 | 0.04 | 0.10 | 0.10 | 0.05 | 0.14 |
| 20 | 0.07 | 0.03 | 0.13 | 0.08 | 0.04 | 0.17 | 0.11 | 0.05 | 0.20 |
| 25 | 0.14 | 0.08 | 0.28 | 0.15 | 0.11 | 0.29 | 0.22 | 0.14 | 0.38 |
| 32 | 0.23 | 0.11 | 0.49 | 0.26 | 0.17 | 0.59 | 0.40 | 0.23 | 0.68 |
| 40 | 0.30 | 0.17 | 0.68 | 0.40 | 0.23 | 0.86 | 0.51 | 0.29 | 1.02 |
| 50 | 0.50 | 0.25 | 0.85 | 0.70 | 0.4 | 1.28 | 0.91 | 0.59 | 1.59 |
| 65 | 0.85 | 0.48 | 1.41 | 1.40 | 0.77 | 2.19 | 1.81 | 0.99 | 3.13 |
| 80 | 1.25 | 0.63 | 1.77 | 2.20 | 1.08 | 3.31 | 2.97 | 1.50 | 4.45 |
| 90 | 1.70 | 0.75 | 2.67 | 2.83 | 1.42 | 4.08 | 4.00 | 2.00 | 5.44 |
| 100 | 2.10 | 1.08 | 3.46 | 4.47 | 2.09 | 5.27 | 6.18 | 2.81 | 7.71 |
| 150 | 5.45 | 2.72 | 8.07 | 10.89 | 5.44 | 10.99 | 16.32 | 8.16 | 13.61 |
| 200 | 10.20 | 5.33 | 15.65 | 21.54 | 10.77 | 20.91 | 33.11 | 16.56 | 28.12 |
| 250 | 18.15 | 9.75 | 26.46 | 38.56 | 19.27 | 35.38 | 51.71 | 25.86 | 49.90 |
| 300 | 25.80 | 13.62 | 39.46 | 59.42 | 29.71 | 62.14 | 79.38 | 39.69 | 83.91 |
| Product range and theoretical weights (kg) | |||||||||
| DN | Schedule 10S | Schedule 40S | Schedule 80S | ||||||
| Con reducer | Ecc reducer | Reducing tee | Con reducer | Ecc reducer | Reducing tee | Con reducer | Ecc reducer | Reducing tee | |
| 40x.25 | 0.19 | 0.19 | 0.60 | 0.26 | 0.26 | 0.76 | 0.34 | 0.34 | 0.90 |
| 50x25 | 0.28 | 0.28 | 0.73 | 0.40 | 0.40 | 1.10 | 0.54 | 0.54 | 1.37 |
| 50x40 | 0.31 | 0.31 | 0.76 | 0.45 | 0.45 | 1.15 | 0.59 | 0.59 | 1.43 |
| 80x.50 | 0.55 | 0.55 | 1.56 | 1.00 | 1.00 | 2.91 | 1.79 | 1.79 | 3.91 |
| 100x50 | 0.78 | 0.78 | 2.94 | 1.50 | 1.50 | 4.48 | 1.95 | 1.95 | 6.55 |
| 100x80 | 0.87 | 0.87 | 3.04 | 1.74 | 1.74 | 4.64 | 2.33 | 2.33 | 6.79 |
| 150x80 | 1.82 | 1.82 | 6.86 | 3.95 | 3.95 | 9.68 | 5.51 | 5.51 | 11.57 |
| 150x100 | 1.96 | 1.96 | 7.10 | 4.07 | 4.07 | 11.94 | 5.96 | 5.96 | 11.97 |
| 200x100 | 3.01 | 3.01 | 13.46 | 6.55 | 6.55 | 17.98 | 9.23 | 9.23 | 24.18 |
| 200x150 | 3.19 | 3.19 | 14.08 | 6.74 | 6.74 | 18.82 | 10.12 | 10.12 | 25.31 |
Inconel 600 Pipe Fittings Tolerance Chart
| Nominal Diameter | O.D.For Bevel End | I.D.For End | Wall Thickness | Elbow | Tee | Reducer | Cap | 180°Elbow | |||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| DN | NPS | A | B | C | M | H | E | O | K | Roughness | |||
| 15-65 | 1/2-2 1/2 | +1.6/-0.8 | 0.8 | -12.50% | 1.6 | 1.6 | 1.6 | 1.6 | 1.6 | 3.2 | 6.4 | 6.4 | 0.8 |
| 80-100 | 3-4 | 1.6 | 1.6 | 6.4 | |||||||||
| 125-200 | 5-8 | +2.4/-1.6 | |||||||||||
| 250-450 | 10-18 | +4/-3.2 | 3.2 | 2.4 | 2.4 | 2.4 | 2.4 | 2.4 | 9.6 | ||||
| 500-600 | 20-24 | +6.4/-4.8 | 4.8 | 3.2 | 3.2 | 3.2 | 3.2 | 4.8 | 9.6 | ||||
| 650-750 | 26-30 | ||||||||||||
| 4.8 | 4.8 | 4.8 | 4.8 | ||||||||||
| 800-1200 | 32-48 | ||||||||||||
| 1250-1500 | 50-60 | +9.6/-6.4 | 6.4 | 9.6 | 9.6 | 9.6 | 9.6 | 9.6 | |||||
| 1550-1750 | 62-70 | +12.7/-9.6 | 9.6 | 12.7 | 12.7 | ||||||||
| 1800-2000 | 72-80 | +16/-12 | 12 | 16 | 16 | ||||||||
Largest Inventory Of Inconel 600 Pipe Fittings
- DIN 2.4816 Reducer
- UNS N06600 Butt weld Elbow
- Inconel 600 45 Deg Elbow
- Inconel® Alloy 600 Pipe Bend
- ASTM B366 Inconel Alloy 600 Reducing Nipple
- DIN 2.4816 Two Halve Butt weld Fittings
- UNS N06600 Lap Joint Stub End
- Inconel 600 SR Elbow
- Nickel Alloy 600 Equal Cross
- Inconel 600 Reducing Cross
- ASME B16.5 Nickel Alloy 600 Buttweld Fittings
- Inconel 600 Pipe Fittings
- Inconel® Alloy 600 180° LR Return Bends
- DIN 2.4816 Welded Fittings
- Inconel 600 End Cap
- UNS N06600 90° Short Radius Elbow
- Alloy 600 Elbow
- Inconel Alloy 600 Pipe Elbow
- 600 PN 16 Inconel Pipe Nipple
- ASME SB366 Nickel Alloy 600 Long Radius Bend
- UNS N06600 Butt weld Nipple
- ASTM B366 Inconel 600 Buttweld Fittings
- Inconel Alloy 600 Long Stub End
- ANSI B16.5 Inconel 600 Pipe Fittings
- DIN 2.4816 Stub End
- Incoloy 600 LR Elbows
- Alloy 600 1D Elbow/3D Elbow/5D Elbow
- UNS N06600 Long Stub End
- ANSI B16.5 Inconel 600 Mandrel Bend
- Inconel® Alloy 600 90° Short Radius Elbow
- ASME SB366 Nickel Alloy 600 Eccentric Reducer
- WERKSTOFF NR. 2.4816 Barrel Nipple
- 600 Inconel Butt weld Fittings
- Alloy 600 Lateral Tee
- Inconel 600 Industrial Pipe Fittings
- Inconel Alloy 600 Two Joint Pipe Fittings
- DIN 2.4816 Butt weld Tee
- UNS N06600 BS 4504 Piggable Bend
ASTM B366 Inconel Alloy 600 Pipe Fittings Application
